Woodworking

All Woodworking Projects

Woodworking Plans [ALL FREE!]

Project Hutchinson – Home Remodeling Projects

My Shop Tour (2017 – Video)

My Shop Tour (2011) (Photos)

 

Working Large Slabs – Introduction

I made a router jig for flattening large slabs. It is based off of Nick Offerman’s design that I saw in an issue of Fine Woodworking a few years ago. I’ll draw up the dimensions... [read more]
Woodworking

Kitchen Remodel Progress

My kitchen remodel is going slow, but I finally got to the point where I could install some of the cabinets! Next up will be a concrete countertop.
Project Hutchinson, Woodworking

Kitchen Cabinets: Introduction and Sketchup

I’m remodeling my kitchen and building new cabinets out of alder wood. I like to remember what I did, so I’ll write up some details for the next wood working project I tackle. The first... [read more]
Project Hutchinson, Woodworking

Video: Alaskan mill used to make oak wood slabs!

Hey guys! In this "adventures of Corbin" episode I'm using my Alaskan Mill to make my own oak wood slabs! Check it out in case you are interested in doing it yourself, as I go over the basics on what I did. A pretty large oak tree fell down on my property last summer, and I wanted to see if I could get some usable wood of it. This is my second time using an alaskan mill, and it is a lot of hard work, but good fun. If you liked the video, subscribe! It encourages me to make more cool films.
Video, Woodworking

Woodworking: Jewelry Rack

My wife requested one thing for Christmas: a custom made jewelry rack. Originally I was thinking of welding something together out of old gears and sprockets, but the power went out right when I was... [read more]
Woodworking
no_thumbnail

Chesapeake 16LT Kayak: It hits the water

In October 2016 I got a wooden kayak kit. In February 2017 it finally hit the water! It took a little longer than I expected, but I’m happy with the result! Here I am taking... [read more]
General, Woodworking

Chesapeake 16LT Kayak: Part 14 – Finished.

Happy days are here! Actually, most all my days are happy days, but the kayak is done! I installed the seat and hatch straps. The seat is just some foam glued in, and in the... [read more]
General, Woodworking
no_thumbnail

Chesapeake 16LT Kayak: Part 13: Wet sanding

I did some wet sanding on the kayak after the first coat. The directions say to use 400 grit, but I wet sanded the first two coats with 320, and then switched to 400 for... [read more]
General, Woodworking

Chesapeake 16LT Kayak Part 12: Starting the finishing process

I was gone for a few weeks in Japan, so progress on the kayak has been slow. I’m back to doing some work on it. First I had to sand it a ton. 80 grit,... [read more]
General, Woodworking
no_thumbnail

Chesapeake Kayak: Almost done (video)

   
General, Woodworking

Building the Chesapeake 16LT Kayak: Part 11 – Mark and Cut Holes

Okay! Progress is happening when I have spare time. I glued on the cowling around the opening, cut it to fit and sanded it smooth. The glue-up was a bit tricky…I didn’t have quite enough... [read more]
General, Woodworking

Building the Chesapeake 16LT Kayak: Part 10 – Top Coat

I used 4oz fiberglass on top, per the instructions in the kit. I was afraid I was going to run out of epoxy hardener, so I only glassed half of the boat at first. This... [read more]
General, Woodworking

(c) 2008-2019 Corbin Dunn

Privacy Policy

Subscribe to RSS feeds for entries.

68 queries. 0.633 seconds.

Log in